grille, dashboard, interior trim, door panel, sunshade panel, seat side

Contact us

cooperationlike@gmail.com

Car shipping companies always pay attention to the sound affected by high temperature and humidity. Now most cars are equipped with CD equipment. The main factors that affect the normal work of car audio in autumn are high temperature and humidity. Because the car audio is mostly installed in the upper part of the dashboard, in order to avoid the exposure of the sun, the effect of using sunshade is better. If the door and window sealing strip is not strict, it should be replaced, otherwise the loudspeaker is easy to rust and damage, or even cause short circuit to burn the main engine.

In addition, its adaptability to temperature is relatively poor, only in a temperature suitable for its growth, it can grow and develop normally. So if the climate of your area does not match its growth conditions, then you need to build a greenhouse for it to adjust the temperature of its surroundings. Zucchini can only grow in the range of 15 to 30 degrees Celsius, and the best temperature is about 20 degrees Celsius, so if the temperature drops suddenly, be sure to keep them warm. They can be covered with some thatch or covered with plastic film. When the temperature is high, you can pull the sunshade net for it or increase the ventilation in the garden. This keeps the enzyme in the zucchini at its highest activity, allowing it to grow faster.

grille, dashboard, interior trim, door panel, sunshade panel, seat side

As can be seen from the above picture, through horizontal shading, a certain direct area can be reduced on the outer window, which makes the radiation heat to the building caused by the heat of the outer window (red wave arrow part). At the same time, through the upper reflective surface of the sunshade, the sunlight is reflected to the ceiling of the building, and then through the diffuse reflection of the ceiling, the daylighting inside the building is increased (orange wave arrow part). It should be noted that this part of the reflected light also brings part of the energy into the room, which will cause indoor load, but the heat of reflected radiation can be reduced by using selective reflection coating, therefore, the heat caused by this part of solar reflected radiation can be considered to be much less than that caused by direct sunlight.

TRX1 class equipment package (body color door handle, front door accent lighting, full-length advanced upgrade floor console, heating steering wheel, internal auxiliary handle, IPLED environment light tube, leather trimmed barrel seat, 4-way headrest, bucket seat, front heating seat, front seat backrest map pocket, electric four-way drive waist adjustment, electric four-way passenger waist adjustment, rear 60tap 40 split folding bench, luxury front door trim panel Mopar bright pedal kit, pickup box lighting, electric 8-way driver / passenger seat, power adjustable pedal, advanced package dashboard bezel, rain sensitive windscreen wiper, rear door accent lighting, rear seat compartment storage space, rear window defroster, sunshade with illuminated cosmetic mirror, general garage door opener) optional: two-pane panoramic skylight pedal car body sticker

grille, dashboard, interior trim, door panel, sunshade panel, seat side

Among them, Lijin FA two-plate high-performance large injection molding machine adopts a unique two-plate clamping structure and an optimal combination design that integrates mechanical, hydraulic and control. The maximum clamping force can reach 70000KN. Its efficient and stable control system is more suitable for auto parts molding and lightweight requirements, with high-quality servo pump group, minimizing production energy consumption. It is suitable for the intelligent production demand of large-scale deep cavity products, and the models in the auto parts industry are concentrated in 450-4500 tons. It is mainly used to produce automobile bonnet, front and rear bumper, exterior decoration electroplated parts, front grille, dashboard, interior trim, door panel, sunshade panel, seat side cover and other parts, equipped with professional injection molding machine controller, single cylinder injection system, high repetition precision, large modulus and opening stroke, high quality hydraulic sealing technology. Improve the durability and reliability of the machine.

In the hot summer sun, the temperature in the car can rise to the point where it is impossible to enter, and car shading is a convenience that can slow down the warming rate. Many car sunshades on the market are called car sunshades, some are suitable for affixing on the outside of the car, some can be fixed in the car, and can also be subdivided into front windshields or side windows, plus the size and function are not the same.

grille, dashboard, interior trim, door panel, sunshade panel, seat side

In order to achieve the welding effect, we can weld multiple points in the same spot, cut and seal, and use the working rules of ultrasonic instantaneous vibration to cut chemical fiber fabric. the highlight of this method is that the incision is smooth, non-cracking and non-wiredrawing. Electric energy is converted into mechanical energy by ultrasonic vibration. Energy is transferred to the contact surface of the plastic workpiece through HORN, resulting in the principle of strong intermolecular friction and heat generation. The product will immediately melt and integrate into the same 360 degrees. Such as: speakers, dashboards, folders, lamps, vacuum cleaners, filters, electric mosquito rackets and so on. Double-head ultrasonic plastic welding machine, can give full play to its welding effect when welding hard plastic materials, ultrasonic welding machine, special scope: used for car body plastic parts, car doors, car instruments, headlamps, mirrors, sunshades, interior decoration, filters, plastic electronic products: prepaid water meters, electricity meters, communication equipment, cordless phones, mobile phone accessories.

By admin